
UNIFIED MODULAR MECHANICAL STANDARD
Engineering Standard for Modular Fixture Plates
This standard establishes a unified mechanical language across all Infinity Skies products. It governs how components interface, align, mount, stack, reference, and integrate at every level from individual machined parts to full system assemblies. The scope of this standard includes, but is not limited to:
- Machined interface plates
- Fixture and tooling components
- Structural interface blocks
- Equipment mounting systems
- Test and automation assemblies
- Modular frames, carts, and platforms
All Infinity Skies products either fully comply with this standard or explicitly declare deviations.
1. Purpose and scope
This standard sets how our plates and step adapters are dimensioned, marked, mounted, and inspected. It covers grid plates in three tiers, step adapters, and datum blocks, pins, stops, clamps, frames, and tool or robot mounts built to the grid. Products either meet this standard or state their deviations.
2. Design principles
- Reuse first. Every component is designed to work in more than one setup.
- Controlled interfaces. We control the mounting interface so plates stay compatible over time.
- Datum discipline. Every component is built around defined datums for repeatable assembly.
- Room to grow. Setups can be expanded, stacked, or recombined without redesigning existing parts.
3. The three grids
| Tier | Name | Hole | Pitch | Material |
|---|---|---|---|---|
| 1 | Foundation Grid | 5/8 in | 2.000 in | Mild steel |
| 2 | Production Fixture Grid | 3/8-16 | 1.000 in | 6061-T651 aluminum |
| 3 | CMM & Inspection Grid | 1/4-20 | 0.500 in | 6061-T651 aluminum |
- Nested positions. The first hole sits 1.000 in from the datum edges on every plate, so every Tier 1 position is also a Tier 2 and Tier 3 position.
- Plate size. Plates are whole inches.
- Hole addresses. Columns are lettered A, B, C along X, and rows are numbered 1, 2, 3 along Y, with A1 at the lower left. Hole center X = 1.000 in + (column − 1) × pitch, and Y works the same way.
- Step adapters. A plate with smaller holes mounts on a plate with larger holes through a step adapter, and the adapter takes the larger plate’s thread on one end and the smaller plate’s on the other.
4. Datums
Every Infinity Skies component defines a consistent datum structure:
- Datum A: Primary mounting or reference face
- Datum B: Orthogonal alignment face or edge
- Datum C: Secondary alignment or rotational control feature
5. Holes and fasteners
| Tier | Thread | Tap drill | Clearance (mount hole) | Min thickness | Thicknesses offered |
|---|---|---|---|---|---|
| 1 | 5/8 in hole | n/a | n/a | 0.750 in | 0.750, 1.000 in |
| 2 | 3/8-16 UNC-2B | 5/16 in | 0.397 in | 0.625 in | 0.625, 0.750, 1.000 in |
| 3 | 1/4-20 UNC-2B | #7 (0.201 in) | 0.257 in | 0.375 in | 0.375, 0.500 in |
Default fasteners are socket head cap screws in the plate’s thread size, with dowel pins for alignment.
6. Materials and finishes
- Tier 1: mild steel, raw with corrosion-preventive oil, or black oxide.
- Tiers 2 and 3: 6061-T651 aluminum, as machined or anodized (clear or black).
- Step adapters: steel, 6061-T651 aluminum.
- Custom fixtures: other alloys by engineering approval.
7. Tolerances (Revision A)
| Feature | Requirement |
|---|---|
| Hole position, Tiers 2 and 3 | 0.003 in position zone to datums A, B, C |
| Hole position, Tier 1 | 0.010 in position zone to datums A, B, C |
| Plate length and width | Nominal +0.000 / −0.005 in |
| Flatness and parallelism, Tiers 2 and 3 | 0.003 in over any 12 × 12 in area |
| Flatness and parallelism, Tier 1 | 0.010 in over any 12 × 12 in area |
| Surface finish, top and bottom faces | 63 microinch Ra max |
Hole entries and edges are broken 0.010 to 0.030 in. Dimensions and threads apply after finishing. Tighter tolerances for custom parts are called out on the drawing.
8. SKU and configuration control
[TIER]-[PART]-[SIZE]-[MATERIAL]-[FINISH]
Example: T2-FBP-1212-AL-AN2 is a Tier 2 fixture base plate, 12 × 12, 6061 aluminum, black anodize.
- Tier: T1, T2, T3
- Part: BP base plate, FBP fixture base plate, LPN locating pin, AST adjustable stop, IBP inspection base plate
- Size: 1212, 1818, 2424, or CSTM for a custom envelope
- Material: AL 6061, MS mild steel, HS hardened steel, SS stainless
- Finish: RW raw, AN1 clear anodize, AN2 black anodize, BO black oxide, ZN zinc, PC powder coat
Kits and assemblies get their own SKU and reference a bill of materials. Child parts keep their own revisions. Changes are documented, and backward compatibility is kept where possible. Deviations are documented with the reason and the compatibility impact.
9. Marking and inspection
Each plate is marked with part number and tier on an edge, and with column letters and row numbers on the top face. The first unit of each part number is fully inspected. Threads are checked with go and no-go gages. Material is traceable to its mill certificate.